வெட்டுவதற்கு கடினமான பல பொருட்களின் பாகங்களை திருப்புதல்

இந்த கட்டுரை கடினமான எஃகு மாற்றுவதற்கான செயல்முறை அமைப்புகளை பகுப்பாய்வு செய்கிறது, உயர் வெப்பநிலை கலவை, டைட்டானியம் கலவை, குளிர்ந்த வார்ப்பிரும்பு, மற்றும் வெப்ப தெளிப்பு பொருள் பாகங்கள். மற்றும் இந்த கடினமான வெட்டப்பட்ட பொருட்களின் பண்புகள், வெட்டு அளவுகள், திருப்பு திரவங்கள், மற்றும் திருப்பு கருவிகள்.
கடினப்படுத்தப்பட்ட எஃகு திருப்பு தொழில்நுட்பம்
1. Turning of hardened steel:
① Cutting characteristics of hardened steel:
1) High hardness: HRC45-70.
2) High brittleness.
3) High strength: σb = 2100～2600 MPa, which is about 4 times that of 45 எஃகு.
4) Large cutting force: The unit cutting force Kc is 4500MPa, எது 2.5 times that of 45 எஃகு.
5) உயர் வெட்டு வெப்பநிலை: its thermal conductivity is 1/7 இன் 45 எஃகு.

கடினப்படுத்தப்பட்ட எஃகு திருப்பு தொழில்நுட்பம்

② Turning tool and cutting amount of hardened steel:
1) Tool materials: PCBN, மட்பாண்டங்கள், சிமென்ட் கார்பைடு (600, 610, YS8, YT05, 758, 813), முதலியன.
2) Tool geometry parameters: γ0=0～-10°, workpiece hardness and continuous cutting γ0=-10～-30°, α0=8～10°, κr=30～60°, λs=0～-3° .
3) Cutting amount: cemented carbide Vc=30～50m/min; Ceramic tool Vc=60～120m/min; PCBN tool Vc=100～200 m/min, Vc is 1/2 of the above during intermittent turning, and αp and f are 1/2 of general steel.

குறிப்பு: பொதுவாக, the heat resistance of quenched steel is 200～400℃, and its hardness decreases with increasing temperature. The heat resistance of tool materials (hard alloys, மட்பாண்டங்கள், PCBN) are respectively 800～1000℃, 1200℃, 1400～1500℃, using this feature, in continuous cutting, Vc cannot be selected too low; When drilling, Vc should be reasonable, and the tool should be retracted; During continuous cutting, f should be small, κr should be appropriately reduced, γε increased, and λs should be negative.
Turning technology of superalloy

Turning technology of superalloy

2. Turning of superalloy
Because the high-temperature alloy contains many high melting point alloying elements Fe, Ti, Cr, இல், வி, டபிள்யூ, Mo and so on. This element and other alloying elements form an austenitic alloy with high purity and dense structure. The contained elements and the non-metallic elements C, பி, என், முதலியன. form metal and non-metal compounds with high hardness, low specific gravity, and high melting point. Make other machinability very poor. Its relative turning workability is only 5-20% இன் 45 எஃகு.

① Turning characteristics of superalloy:
1) Large cutting force: 2 செய்ய 3 times larger than cutting general steel.
2) உயர் வெட்டு வெப்பநிலை: 50% higher than cutting 45 எஃகு.
3) Severe work hardening: the hardness of the cutting surface and the machined surface is 50-100% higher than that of the matrix.
4) Tools are easy to wear: adhesion, diffusion, ஆக்சிஜனேற்றம், and groove wear are easy to occur.

②Materials for turning tools of high-temperature alloys:
1) High-speed steel: High-speed steel containing high vanadium, high carbon and aluminum should be used.
2) Cemented carbide: fine and ultrafine particles of YG should be used

③ Geometric parameters of turning tools for high-temperature alloys:
Deformed superalloy: γ0=10°, cast superalloy: γ0=0°, generally do not take negative chamfering. α0=10～15°, rough turning λs =-10°, fine turning λs=0～3°, κr=45～75°.

④ Turning amount of superalloy:
1) High-speed steel cutter: Vc=3～8m/min.
2) Carbide tool: Vc=10～60 m/min. Deformed superalloy: Vc=40～60m/min. Casting high-temperature alloy: Vc=7～10m/min. αp and f>0.1மிமீ.

⑤ Cutting fluid for high-temperature alloys: the same as stainless steel.
⑥ Drilling of high-temperature alloys: Carbide drills or S-type and shallow hole drills should be used as far as possible; உதாரணத்திற்கு, when using a high-speed steel drill, increase the size of 2 wires, grind α0 and b, Vc is 3 m/min, and f is 0.2～0.3mm/r; The drill bit should be sharp, and the standard for bluntness is 1/2 செய்ய 1/3 of that of general steel. It is best to use automatic feed, do not stop on the cutting surface.

டைட்டானியம் பாகங்களை திருப்புதல் தொழில்நுட்பம்

டைட்டானியம் பாகங்களை திருப்புதல் தொழில்நுட்பம்
3. Turning of titanium alloy:
Titanium alloy is a new metal developed in recent decades. Because of its high specific strength (σb/ρ=1680/4.5=373, 4.5 times that of 45 எஃகு), high thermal strength (long-term work at 500℃), good corrosion resistance, and excellent low temperature performance, it is used in aerospace, chemical engineering , Medical treatment, முதலியன.

① Cutting characteristics of titanium:
1) The cutting temperature of titanium is high: under the same cutting conditions, it is twice as high as cutting 45 எஃகு.
2) Titanium has a great affinity and serious bonding, which will cause bonding at high temperatures.
3) Titanium has high chemical activity: under high temperature cutting conditions, it reacts with O, என், எச், C in the air to form a hard skin layer of TiO2, TiN, TiH, முதலியன, which brings difficulties to cutting.
② Tool materials for turning titanium:
1) High-speed steel: In addition to ordinary high-speed steel, it is best to use high-vanadium, high-cobalt, and aluminum-containing high-speed steel.
2) Cemented carbide: YG8, YG6X, YG6A, 813, 643, YS27, YD15.3) PCD, PCBN natural diamond.
③ Tool geometry parameters: γ0=5～15°, α0≥15°.

④ Turning amount of titanium:
1) High-speed steel cutter: Vc=8～12 m/min.
2) Cemented carbide tools: Vc=15～60 m/min.
3) PCD, PCBN natural diamond tools: wet cutting Vc=200 m/min
Dry cutting Vc=100 m/min, αp>0.05மிமீ, f>0.05mm/r.

⑤ Titanium cutting fluid: Emulsion and extreme pressure emulsion are used for one. Extreme pressure cutting oil is used for finishing.
⑥ Note for turning titanium:
When turning a slender shaft (rod), the live center and nylon should be used as the claw holder of the tool holder and the center frame; When reaming, use castor oil 60% + kerosene 40% as cutting fluid; When tapping, appropriately increase the diameter of the bottom hole.

4. Turning of chilled cast iron:
The surface layer of the cast iron is white mouthed, and the hardness can reach about HRC60; The unit cutting force K c can reach 3000 MPa, எது 1.5 times that of cutting 45 எஃகு; The cutting force is concentrated near the cutting edge, and there are pores and sand in the machining, which can easily damage the tool during cutting;
Its brittleness is large, and the phenomenon of edge chipping and slag falling will occur during cutting.
① Tool material for turning cast iron:
1) Cemented carbide: a cemented carbide with high hardness and bending strength should be selected. போன்ற: YS2, YS8, YS10, 600, 610, 726.
2) Ceramics: SG4, AT6, SM, FT80, FT85.
3) PCBN: used for fine turning.

② The geometric parameters of the tool for turning cast iron: 1) Carbide: γ0=0～-5°, α0=5～10°, κr≤45°(κr=45°), λs =-5～一10°, γε =0.5～1 mm;

③ The amount of cutting cast iron:
1) Carbide tool: rough machining Vc=7～10m/min, αp=5～10mm, f=0.5～1.5mm/r. Finishing: Vc=15～20m/min, αp=0.5～2mm, f=0.3～0.5mm/r.
2) Ceramic tools: Vc=40～50m/min, αp=0.5～2mm, f=0.3～0.6mm/r.
3) PCBN cutter: Vc=60～70m/min, αp=0.5～2mm, f=0.1～0.3mm/r.

5. Turning of thermal spraying (வெல்டிங்) பொருட்கள்:
Thermal spraying materials are mostly multi-component high-strength alloys. After high temperature and high speed spraying on the surface of the workpiece, the hardness, அரிப்பு எதிர்ப்பு, wear resistance and heat resistance of the surface of the workpiece are greatly improved, and it is widely used. The hardness of the copper-based and iron-based powder spray coating is easier to cut. The hardness of the cobalt-based and nickel-based powder spray coating is >HRC50, which is difficult to cut. Cobalt-clad WC, nickel-clad WC, and nickel-clad Al2O3 spray coatings have hardness> HRC65, which is the most difficult to cut.
① Tool materials for turning thermal spraying materials:
1) Cemented carbide: கடினத்தன்மை>HRC45, using YG, YW cemented carbide;
Hardness, using 600, 610, 726, 767, YD05, YC12, YS2, YS8;
Hardness>HRC65, use YG3X, YD05, YC09, YC12, YS8, 600, 610.
2) Ceramic cutter: 3) PCBN
② The geometric parameters of the tool when turning thermal spray materials: γ0=0～-5°, α0=8～12°, κr≤45°.
③ The amount of cutting thermal spraying material: cemented carbide Vc=6～40m/min;
Ceramic cutter Vc=18～80m/min;
PCBN tool: Vc=24～160m/min. αp=0.15～0.6mm; f=0.1～1mm/r.