Категории продукта
Теги продукта
Недавние Посты
Крепеж и наладка токарных деталей токарных станков
Зажим токарных инструментов
1) Хвостовик токарного инструмента не должен слишком долго выступать из держателя инструмента., а общая длина не должна превышать 1.5 умноженная на высоту хвостовика инструмента (кроме поворотных отверстий, канавки, и т. д.)
2) Центральная линия стержня токарного инструмента должна быть перпендикулярна или параллельна направлению резания..
3) Регулировка высоты кончика инструмента:
Категория: токарные услуги с ЧПУ
Ярлык: Токарная обработка с ЧПУ
General technical code for turning metal processing (JB/T9168.2-1998)
Зажим токарных инструментов
1) Хвостовик токарного инструмента не должен слишком долго выступать из держателя инструмента., а общая длина не должна превышать 1.5 умноженная на высоту хвостовика инструмента (кроме поворотных отверстий, канавки, и т. д.)
2) Центральная линия стержня токарного инструмента должна быть перпендикулярна или параллельна направлению резания..
3) Регулировка высоты кончика инструмента:
(1) When turning the end face, turning taper surface, токарная резьба, turning forming surface and cutting solid workpieces, the tool tip should generally be the same height as the axis of the workpiece.
(2) Rough turning of the outer circle, fine turning of the hole, and the tool tip should generally be slightly higher than the axis of the workpiece.
(3) When turning slender shaft pins, rough turning holes, and cutting hollow workpieces, the tool tip should generally be slightly lower than the axis of the workpiece.
4) The bisector of the nose angle of the thread turning tool should be perpendicular to the axis of the workpiece.
5) When clamping the turning tool, the shims under the tool bar should be small and flat, and the screws for pressing the turning tool should be tightened.
Clamping of turning hardware parts
1) When using a three-jaw self-centering chuck to clamp a workpiece for rough turning or finishing turning, if the diameter of the workpiece is less than 30 мм, the overhang length of the workpiece should not be greater than 5 раз больше диаметра. If the diameter of the workpiece is greater than 30 мм, the overhang length of the workpiece should not be greater than 3 раз больше диаметра.
2) When using four-jaw single-action chuck, faceplate, angle iron (bent plate), и т. д.. to clamp irregular and heavy workpieces, a counterweight must be added.
3) When machining shaft pin workpieces between thimble fixtures, adjust the tailstock center axis to coincide with the lathe spindle axis before turning.
4) When machining a slender shaft between two thimble fixtures, the tool holder or center holder should be used. Pay attention to adjusting the top tightening force during processing, and the dead center and center frame should be lubricated.
5) When using the tailstock, extend the sleeve as short as possible to reduce vibration.
6) When clamping a workpiece with a small supporting surface and high height on a vertical car, use a raised jaw and add a tie rod or a pressure plate to the appropriate position to compress the workpiece.
7) When turning wheel and sleeve castings and forgings, they should be aligned according to the unprocessed surface to ensure uniform wall thickness after processing.
Turning process of hardware parts
1) When turning the stepped shaft of the turning table, in order to ensure the rigidity during turning, generally the position with the larger diameter should be turned first, and the position with the smaller diameter should be turned later.
2) When grooving the workpiece on the shaft, it should be performed before finishing to prevent deformation of the workpiece.
3) When finishing turning a threaded shaft, generally you should finish turning the unthreaded position after threading.
4) Before drilling, the end face of the workpiece should be turned flat. Если необходимо, drill the center hole first.
5) When drilling deep holes, generally drill pilot holes first.
6) When turning (Φ10—Φ20) ㎜ holes, the diameter of the tool bar should be 0.6—0.7 times the processed hole diameter;
When machining holes with a diameter greater than Φ20mm, generally the tool holder with the turning head should be used.
7) When turning multiple threads or multiple worms, try cutting after adjusting the gears.
8) When using an automatic lathe, adjust the relative position of the tool and the workpiece according to the adjustment card of the machine tool. After the adjustment is completed, test turning is required, and the first part can be processed only after it is qualified;
Pay attention to tool wear and workpiece size and surface roughness at any time during processing.
9) When turning on a vertical lathe, after the tool post is adjusted, the beam cannot be moved at will.
10) When the relevant surface of the workpiece has position tolerance requirements, try to complete the turning in one clamping.
11) When turning the cylindrical gear blank, the hole and the reference end face must be processed in one clamping. Если необходимо, a marking line should be drawn near the gear index circle on the end face.
Связаться с нами
Жду вашего письма, мы ответим вам в течение 12 часы с ценной информацией, которая вам нужна.
СОПУТСТВУЮЩИЕ ТОВАРЫ
Изготовленные на заказ прецизионные токарные детали из меди
Наша компания хорошо выполняет токарную обработку всех видов медных деталей., все виды деталей клапана, электрические бронзовые детали, латунные гайки, антенны мобильного телефона, внешняя накатка (прямое зерно / саржа / чистое зерно) и так далее. На рисунке слева показан точеный медный сердечник.. Используется в клапанах, материал — быстрорежущая сталь C3604, латунь., а медные токарные детали, изготовленные по индивидуальному заказу, используются в качестве стержня и сердечника клапана.. Используется в клапанах всемирно известных брендов.. Автоматическое точение и формование, после кромки фрезерования головки и кромки фрезерования стержня, угол 60 степени. Головка с прорезями. Внешний диаметр 12,7 мм., и общая длина 70 мм.. Токарно-формующий инструмент много раз использовался при обработке этой прецизионной медной детали.. Для решения проблемы точности угла R и снятия фаски внутренней канавки, Первоначально была принята обработка с ЧПУ.. Позже, чтобы сэкономить затраты, использована автоматическая токарная обработка.
Разница между токарным автоматом и токарным станком с ЧПУ
Different metal nuts processed by automatic lathe
Our company provides automatic lathe processing of various nuts, включая, помимо прочего, вставные гайки для литья под давлением, как показано на рисунке слева.. В других каталогах на этом сайте имеется большое количество примеров этого продукта.:
В комплект также входят шестигранные и тонкие медные гайки., нестандартные специальные гайки, и т. д.. Процесс токарной обработки различных гаечных деталей на токарных автоматах..
Токарные детали из автоматной стали, углеродистая сталь, и экологически чистое железо
Наша компания также производит различные токарные детали из автоматной стали из углеродистой стали.. К таким углеродистым сталям относятся:
Free cutting steel 12L14
The picture on the left is a representative carbon steel turning part of our company. Поверхность почернела и окислилась. В целом, вращающиеся детали из углеродистой стали требуют обработки поверхности для предотвращения ржавчины. Доступные виды обработки поверхности включают в себя:
оцинкованный (включая экологически чистый синий и белый цинк и экологически чистый цветной цинк), никелированная, черная окись (как показано на левом рисунке), и т. д..
Токарная обработка и чистовая обработка 6061, 6063, 7075 детали из алюминиевого сплава
Это небольшая алюминиевая деталь, похожая на чашу., который также обрабатывается на токарном автомате. Его размер очень мал, внешний диаметр всего 6 мм, явно не для еды.
В настоящее время доступны следующие марки материалов для токарных деталей из алюминия:: Т6 6061, 6063 дюралюминий, 7075 резка дюралюминия, и 5056 обычный алюминиевый стержень.
Кстати, 2021 алюминиевый стержень, разновидность алюминия с относительно низкой твердостью и относительно плохими механическими свойствами., клиентам обычно не рекомендуется использовать этот материал.