Frees- en draaitechnologie van roestvrij staal

Roestvrijstalen materialen hebben een hoge taaiheid, hoge thermische sterkte en lage thermische geleidbaarheid. Tijdens het frezen en draaien, de plastische vervorming is groot, de verharding van het werk is ernstig, de snijwarmte is te veel, en de warmteafvoer is moeilijk. Dit resulteert in een hoge snijtemperatuur aan de gereedschapspunt, ernstige spaanhechting aan de snijkant, en gevoelig voor ophoping van spaanranden, wat niet alleen de slijtage van het gereedschap verergert, maar beïnvloedt ook de oppervlakteruwheid van het bewerkte oppervlak. In aanvulling, omdat de spanen niet gemakkelijk krullen en breken, het zal het bewerkte oppervlak beschadigen en de kwaliteit van het werkstuk aantasten. Om de verwerkingsefficiëntie en de kwaliteit van het werkstuk te verbeteren, hoe u het gereedschapsmateriaal correct selecteert, de geometrische parameters van het draaigereedschap en de freeshoeveelheid worden als volgt geïntroduceerd:

Stainless steel turning tools

Tools for milling and turning stainless steel
1. The correct choice of milling tool materials. The tool material is the decisive factor to ensure high-efficiency machining of stainless steel. According to the cutting characteristics of stainless steel, the tool material should have sufficient strength, toughness, hoge hardheid, high wear resistance and low adhesion to stainless steel. Commonly used tool materials include cemented carbide and high-speed steel, and tools with complex shapes mainly use high-speed steel materials. Since the cutting speed of high-speed steel cutting stainless steel cannot be too high, it affects the improvement of production efficiency. For simpler turning tools, the tool material should be high-strength, good thermal conductivity cemented carbide, because its hardness, wear resistance and other properties are better than high-speed steel.

Freesgereedschappen van roestvrij staal

Commonly used cemented carbide materials are: Tungsten cobalt type (YG3, YG6, YG8, YG3X, YG6X), tungsten cobalt titanium type (YT30, YT15, YT14, YT5), general type (YW1, YW2). YG cemented carbide has good toughness and thermal conductivity and is not easy to bond with chips. Daarom, it is suitable for rough turning of stainless steel; The hardness, slijtvastheid, heat resistance, oxidation resistance and toughness of YW cemented carbide are good, and they are suitable for stainless steel fine turning processing. When processing 1Cr18Ni9Ti austenitic stainless steel, YT cemented carbide is not suitable. Because Ti in the stainless steel and Ti in the YT-type hard alloy have an affinity, the chips can easily take away the Ti in the alloy, which promotes the increase of tool wear.
Geometric angle of milling and turning tools
2. Choosing the geometric angle of the cutting part of the tool has a great influence on the productivity of stainless steel cutting, tool durability, surface roughness, cutting force and work hardening. Reasonable selection and improvement of tool geometric parameters is an effective way to ensure processing quality, improve efficiency and reduce costs.

Set the geometric angle of the tool for milling stainless steel

The choice of turning tool rake angle γ0:
The size of the rake angle determines the sharpness and strength of the blade. Increasing the rake angle can reduce chip deformation, thereby reducing cutting force and cutting power, lowering cutting temperature, and improving tool durability. Echter, increasing the rake angle will reduce the wedge angle, reduce the strength of the blade, cause chipping of the blade, and reduce the durability of the tool. When turning stainless steel, the rake angle should be appropriately larger without reducing the strength of the tool. When the tool rake angle is large, its plastic deformation is small, the cutting force and cutting heat are reduced, the work hardening trend is reduced, and the tool durability is improved. Over het algemeen, the rake angle of the tool should be 12°～20°.

Selection of lathe tool relief angle α0
In the cutting process, the relief angle can reduce the friction between the flank face and the cutting surface. If the relief angle is too large, the wedge angle will decrease, worsening the heat dissipation conditions, reducing the strength of the cutting edge of the tool, and reducing the durability of the tool; If the relief angle is too small and the friction is serious, the cutting edge will become blunt, increase the cutting force, increase the cutting temperature, and increase the wear of the tool. onder normale omstandigheden, the clearance angle does not change much, but it must have a reasonable value to help improve the durability of the tool. When turning stainless steel, since the elasticity and plasticity of stainless steel are greater than that of ordinary carbon steel, the tool clearance angle is too small, which will increase the contact area between the cutting surface and the turning tool clearance angle. The high temperature area generated by friction is concentrated on the back corner of the turning tool, which accelerates the wear of the turning tool and reduces the finish of the processed surface. Daarom, the clearance angle of the turning tool when turning stainless steel is slightly larger than that when turning ordinary carbon steel. Echter, too large a relief angle will reduce the strength of the blade and directly affect the durability of the turning tool. Daarom, under normal circumstances, the clearance angle of the turning tool should be 6°～10°.

The choice of turning tool entering angle Kr
When the cutting depth ap and the feed amount f remain unchanged, reducing the entering angle Kr can improve the heat dissipation conditions, reduce tool damage, and make the tool cut in and cut out smoothly. Echter, the decrease of the entering angle will increase the radial force, which will easily cause vibration during cutting. Turned stainless steel has a strong tendency to harden and is prone to vibration, which will cause serious work hardening. Daarom, the entering angle should generally be 45°～90°. The specific angle should be selected according to the rigidity and cutting amount of the machine tool, onderdelen, and tool system. The choice of turning tool blade inclination λs The blade inclination can control the chip flow direction. When the blade angle λs is negative, the chips flow to the machined surface; When the blade angle λs is positive, the chips flow to the surface to be processed. In order to prevent the chips from scratching the machined surface, the blade angle λs is a positive value during finishing. When λs is a positive value, the strength of the tool tip is low and first contacts the workpiece, which is easy to damage; When λs is a negative value, the cutting edge has high strength and impact resistance, which can avoid breaking the cutting edge and cut in and out smoothly. When turning stainless steel, the inclination angle of the cutting tool is generally 0°～20°.

Turning amount of stainless steel

3. Selection of turning and milling amount
The amount of turning and milling has a great impact on production efficiency and processing quality. Daarom, after determining the geometric parameters of the tool, a reasonable cutting amount must be selected. When choosing cutting parameters, the following factors should be considered:
1>The cutting amount should be selected according to the hardness of stainless steel and various blanks;
2>The cutting amount should be selected according to the tool material, welding quality and sharpening conditions of the turning tool;
3>The cutting amount should be selected according to the part diameter, machining allowance and lathe accuracy. Tegelijkertijd, in order to suppress the generation of built-up tumors and scales, and improve the surface quality. When using cemented carbide tools for processing, the cutting amount should be slightly lower than turning general carbon steel workpieces, especially the cutting speed should not be too high (vc=50～80m/min);
The cutting depth ap should not be too small to avoid the cutting edge and the tool tip from scratching the hardened layer, ap=0.4～4mm; Daarom, the feed rate f has less impact on tool durability than cutting speed, but it will affect chip breaking and chip removal, strain and scratch the surface of the workpiece, and affect the surface quality of processing. The feed rate is generally f=0.1～0.5mm/r.

Roestvrij staal, vooral austenitisch roestvrij staal, has better plasticity. During cutting, the generated chips are difficult to break, which increases the friction between the chips and the rake face of the tool and increases the cutting force. Tegelijkertijd, work hardening will increase the hardness and strength of the material being cut, which will also increase the cutting force. Om deze reden, on the basis of reasonable selection of tool materials, tool geometric angles and cutting parameters, a comparative test of cutting force was done on stainless steel and 45 staal. The test results show that, under the same cutting amount, the cutting force when machining stainless steel is only 8.5% higher than when machining 45 staal. Reasonable selection of tool materials, tool geometric angles and cutting quantities is completely possible to improve the production efficiency of stainless steel cutting and the quality of processed workpieces.