Machining technology of titanium alloy parts

Turned titanium alloy parts products can easily obtain better surface roughness, work hardening is not serious, but the cutting temperature is high, and the tool wears quickly. In response to these characteristics, the following measures are mainly adopted in terms of tools and cutting parameters:
Turning tool materials: YG6, YG8, YG10HT are selected according to the existing conditions of the factory.
Geometric parameters of turning tools: suitable front and rear angles of the tool, and tool tip rounding.

Turning of titanium alloy parts
Turned titanium alloy parts products can easily obtain better surface roughness, work hardening is not serious, but the cutting temperature is high, and the tool wears quickly. In response to these characteristics, the following measures are mainly adopted in terms of tools and cutting parameters:
Turning tool materials: YG6, YG8, YG10HT are selected according to the existing conditions of the factory.
Geometric parameters of turning tools: suitable front and rear angles of the tool, and tool tip rounding.

Lower cutting speed, moderate feed rate, deeper cutting depth, and sufficient cooling. When turning the outer circle, the tool tip cannot be higher than the center of the workpiece, otherwise the tool will break. When precision turning and turning thin-walled titanium parts, the cutting tool's entering angle should be large, عمومًا 75-90 درجات.

Milling of titanium alloy parts
Milling of titanium alloy parts is more difficult than turning. Because milling is an intermittent cutting, and titanium chips are easy to bond with the cutting edge. When the sticky chip cuts into the workpiece again, the sticky chip hits a small piece of the tool to form a chipping edge, which greatly reduces the durability of the tool.

Titanium alloy milling method: generally use down milling.
Tool for milling titanium alloy: high-speed steel M42.

عمومًا, down milling is not used for processing titanium alloys. Due to the influence of the open space of the screw and nut of the machine tool, the milling cutter acts on the workpiece during down milling. The component force in the feed direction of the part is the same as the feed direction of the tool, which is easy to cause the work table to move freely and form a broken tool.

Titanium alloy parts tapping

For the tapping of titanium alloy parts processing products, due to the small chips, it is easy to bond with the blade and the workpiece, resulting in a large surface roughness and large torque. When tapping taps and improper selection of improper operation can easily form a work-hardened, low processing power and when there is the phenomenon of broken taps.
It is necessary to prefer a threaded tapping tap with a proper thread, and the number of teeth should be less than the standard tap, عمومًا 2 ل 3 teeth. The cutting taper angle should be large, and the taper part is generally 3 ل 4 thread lengths. من أجل تسهيل إزالة الشريحة, a negative inclination angle can also be ground on the cutting cone. Try to choose short taps to add rigidity to the taps. The inverted taper part of the tap should be appropriately enlarged compared to the specification to reduce the conflict between the tap and the workpiece.

Turning of titanium alloy parts

Turning of titanium alloy parts

 Milling of titanium alloy parts

Milling of titanium alloy parts

 Titanium alloy parts tapping

Titanium alloy parts tapping

اتصل بنا

في انتظار لبريدك الالكتروني, سوف نقوم بالرد عليك في غضون 12 ساعات مع المعلومات القيمة التي تحتاجها.

منتجات ذات صله

اطلب اقتباس

املأ نموذج طلب عرض الأسعار الخاص بنا وسنقوم بالرد على رسالتك في أقرب وقت ممكن!


Warning: file(/www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin_data/keywords_reserved.txt): failed to open stream: No such file or directory in /www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin.cls.php on line 141

Warning: file(/www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin_data/keywords_before.txt): failed to open stream: No such file or directory in /www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin.cls.php on line 142

Warning: file(/www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin_data/keywords_after.txt): failed to open stream: No such file or directory in /www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin.cls.php on line 143

Warning: file(/www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin_data/operators.txt): failed to open stream: No such file or directory in /www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin.cls.php on line 144

Warning: file(/www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin_data/operators_before.txt): failed to open stream: No such file or directory in /www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin.cls.php on line 145

Warning: file(/www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin_data/operators_after.txt): failed to open stream: No such file or directory in /www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin.cls.php on line 146

Fatal error: Uncaught TypeError: Argument 1 passed to LiteSpeed\Lib\JSMin::getOperatorsForRegex() must be of the type array, bool given, called in /www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin.cls.php on line 374 and defined in /www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin.cls.php:746 Stack trace: #0 /www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin.cls.php(374): LiteSpeed\Lib\JSMin->getOperatorsForRegex() #1 /www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin.cls.php(180): LiteSpeed\Lib\JSMin->extractRegex() #2 /www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin.cls.php(160): LiteSpeed\Lib\JSMin->min() #3 /www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/src/optimizer.cls.php(301): LiteSpeed\Lib\JSMin::minify() #4 /www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/src/optimize.cls.php(985): LiteSpeed\Optimizer::minify_js() #5 /www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache in /www/wwwroot/cncpartss.com/wp-content/plugins/litespeed-cache/lib/jsmin.cls.php on line 746